| Brand | Car Name | Model | Year | Position |
|---|---|---|---|---|
| Toyota | Tacoma 4wd | — | 1995- | OUT L |
A tie rod end is the outermost ball-jointed connection in the steering linkage — the wear part that transfers steering motion from the rack (or center link) to the steering knuckle at each front wheel. Every steering system, modern rack-and-pinion or older parallelogram, has tie rod ends; they are one of the highest-volume steering wear items in the global aftermarket.
Also known as: outer tie rod end, steering tie rod end, track rod end (UK/EU), TRE.
The steering rack moves left-right in a straight line. The tie rod end converts that lateral push into the angular motion that swings the steering knuckle around its pivot, turning the wheel.
The threaded sleeve between the inner and outer tie rod is the front-toe adjuster — turning it lengthens or shortens the linkage, opening or closing toe. All wheel-alignment toe corrections happen at this joint.
The ball joint inside the tie rod end allows the steering knuckle to rise and fall with the suspension while still transmitting steering input — without it, the steering would bind through bumps.
A forged steel housing with an internal ball stud, sealed greased bearing surface and rubber/polyurethane dust boot. The stud has a tapered shaft with a castellated nut and cotter pin (or a self-locking nut) to lock it into the steering knuckle. Thread direction on the rod sleeve is opposite between left and right sides on most vehicles, allowing toe adjustment without disconnecting the joint.
How often should tie rod ends be replaced?
There is no fixed interval — they are replaced when worn. Typical life is 100,000–150,000 km on paved roads, less on rough or salted roads. Inspect every service: with the wheel off the ground, a good joint has zero perceptible play when the tire is rocked side-to-side.
Can I drive with a worn tie rod end?
Short distances at low speed, yes. A tie rod end that fails completely will result in total loss of steering on that wheel — the wheel will flop free and the vehicle will be undrivable. Replace promptly once a clunk or visible play is detected.
Do tie rod ends always come in pairs?
Not necessarily — left and right are usually sold individually and use opposite-thread rods. However, replacing both sides at the same time is best practice once one shows wear, since the second side will typically fail within a similar timeframe.
Is wheel alignment required after replacement?
Yes. The toe setting is established at the tie-rod sleeve, and any disassembly of the joint changes it. Drive directly to an alignment rack after replacement.
No. Si tratta di un ricambio aftermarket prodotto da SLOOP, realizzato per soddisfare le specifiche OEM. Il codice originale CET-113L è citato in regime di uso referenziale esclusivamente per identificare la compatibilità veicolare — non implica alcuna licenza, approvazione o affiliazione con il costruttore del veicolo. Per i ricambi originali, contattate il vostro concessionario autorizzato.
Verificato per forma, accoppiamento e funzione rispetto alla specifica OEM. I rapporti di prova del materiale e i disegni quotati vengono allegati a ogni preventivo. Per ordini ad alto volume produciamo un'unità campione di pre-serie per la verifica da parte del vostro ufficio controllo qualità prima dell'avvio della produzione principale.
Gestione della qualità certificata ISO 9001:2015, più REACH / RoHS per la conformità UE. Rapporti di prova del materiale e documentazione PPAP disponibili su richiesta per acquirenti di primo livello. I certificati vengono spediti con la prima fornitura di ogni nuovo SKU.
Nessun campione gratuito. Il primo ordine funge da lotto di qualifica. Tratteniamo la produzione fino alla conferma dell'ispezione visiva e dimensionale del primo collo da parte vostra. Se qualcosa è fuori tolleranza, rifacciamo a nostre spese.
100% T/T (bonifico bancario) prima dell'avvio della produzione. Solo in USD. Le coordinate bancarie e la fattura proforma vengono inviate dopo l'accettazione del preventivo. Nessuna dilazione di pagamento; nessuna lettera di credito al primo ordine.
Articoli a magazzino: spedizione entro 15–30 days dalla conferma del pagamento. Produzione su ordine: 90–120 days dalla conferma del pagamento. Trasporto aereo (DHL / FedEx, porta a porta con tracciabilità) 5–7 giorni. Trasporto marittimo 25–40 giorni a seconda del porto di destinazione. Quotazione disponibile FOB Taiwan o DDP magazzino del cliente.
Caricate la vostra richiesta d'offerta completa nella pagina preventivi. Abbiniamo ogni riga del catalogo disponibile e segnaliamo il resto come input per la nostra pianificazione produttiva. Le richieste aggregate orientano direttamente il nostro prossimo ciclo di produzione.